Please select your home edition
Edition
Doyle-OneStop-728x90 NZ site

Urgent safety advisory issued after fatal tether failure in race

by Sail-World NZ and RYA/MAIB (UK) 10 Jan 12:59 NZDT 10 January 2018
A competitor in the Clipper Round the World Yacht Race sailing in the Southern Ocean with the crew all tethered to the jackline. © Clipper Race

The British Marine Accident Investigation Branch has released an urgent safety advisory bulletin following the fatal man overboard incident during the current Clipper Round the World Yacht Race.

The incident took place in the Indian Ocean on November 18, when British solicitor Simon Speirs (60) went overboard from the yacht CV30 after being swept off the bow by a wave. Wind conditions at the time were 20kts gusting 40kts.

He was wearing the correct safety equipment at the time including a safety harness and tether which was attached to the boat.

The tether failed under load and broke. While Simon Speirs was recovered 36 minutes later, he was unable to be revived and was buried at sea some 1500nm from Fremantle.

The preliminary investigation has revealed that the snap clip used to attach Simon Speirs to the yachts jackline had caught under a cleat or similar fitting on the yacht and had become unable to be properly aligned when the man overboard load was applied.

As a result, it appears that the tether hook distorted because of the load angle and released.

The summary of the advisory reads: "To prevent the strength of a safety harness tether becoming compromised in-service due to lateral loading on the tether hook, the method used to anchor the end of the tether to the vessel should be arranged to ensure that the tether hook cannot become entangled with deck fittings or other equipment."

In other words, the tether hook must be free to slide on the jackline or other secure point. The tether hook is designed to be aligned with the angle of the load.

If the tether hook is not aligned to the tether load and has a lateral load applied it may bend/distort and fail to secure the sailor to the boat.

The tether and hook are supplied with one leading brand of safety equipment and similar styles are used by others. It is not known if the reason for the tether hook failure in Simon Spiers' instance has also been a factor in other incidents involving tether failure. According to the video below a tether with load in the designed direction will fail at 2000kgs. With the load carried at an angle the tether hook fails at just 200kgs.

Below Nic Douglass talks with Sir Robin Knox-Johnson and Matt Allen about the tether hook issue and what can be done short and long term about the situation, which is now known.

A safety message this Christmas...

I took the opportunity today to catch up with Sir Robin-Knox Johnston, the CEO and founder of the Clipper Round the World Yacht Race and Matt Allen, the Vice-Chair of World Sailing’s Oceanic & Offshore Committee about the unfortunate failure of a tether clip which led to a casualty on the third leg of the race. Sailing is a safe sport, but education and awareness is important to make sure that we can save lives, and see everyone stay safe over Christmas, a busy time for sailing in this part of the world! Thanks to Matt and Robin for talking with me today in the Rolex Sydney Hobart village at the Cruising Yacht Club Of Australia to make this issue clear to everyone. Stay safe over Christmas, Nic xx

Posted by Adventures of a Sailor Girl on Saturday, December 23, 2017

The full advisory bulletin reads:

Background The sailing yacht CV30 was taking part in the third leg of the Clipper Round the World Yacht Race having left Cape Town on 31 October 2017 bound for Fremantle, Western Australia. At about 1414 local time on 18 November 2017, the yacht was in position 42°30.3’S, 087°36.3’E, approximately 1500nm from Fremantle, when a crew member, Simon Speirs, fell overboard. He was attached to the yacht by his safety harness tether. The hook at the end of the tether that was clipped to a jack-line, deformed and released resulting in him becoming separated from the yacht. Simon Speirs was recovered unconscious onto the yacht but sadly could not be resuscitated.

For the Marine Accident Advisory Board website item click here

Initial Findings Simon Speirs was using a three-point webbing tether attached to the integral harness of his lifejacket that allowed him to clip on to the yacht with a short or long tether.

A safety issue identified during the investigation was that the hook on the end of Mr Speirs’ tether had become caught under a deck cleat (see Figure 1), resulting in a lateral loading that was sufficient to cause the hook to distort (see Figure 2) and eventually release.

The harness tether was certified under ISO12401 (Small craft – Deck safety harness and safety line – Safety requirements and test methods), which is the international standard applicable to this equipment. The standard contains detailed testing requirements that assume the tether and its hooks will be loaded longitudinally rather than laterally.

The tether hook was of a conventional design and quality of build and was commonly used by manufacturers of safety harnesses and tethers that were certified under ISO12401.

When loaded longitudinally, the tether can withstand a load of over 1 tonne. However, when loaded laterally a tether hook will deform at much less load. It is important that tether hooks remain clear of obstructions and are free to rotate to align the load longitudinally.

Safety Lesson To prevent the strength of a safety harness tether becoming compromised in-service due to lateral loading on the tether hook, the method used to anchor the end of the tether to the vessel should be arranged to ensure that the tether hook cannot become entangled with deck fittings or other equipment.

Related Articles

New research: Boaties behaving more safely!
New research released today shows recreational boaties are behaving more safely but Maritime NZ is w New research released today shows recreational boaties are behaving more safely but Maritime NZ is warning them not to slip up on their good work this summer. Posted on 14 Oct
Master opts to head south in holed ship
Life-threatening incident in the remote New Zealand Sub-Antarctic islands A French cruise company and ship's Master have been fined $70,000 and $30,000 respectively for endangering human life and entering a prohibited zone following an incident in the remote New Zealand Sub-Antarctic islands. Posted on 3 Oct
Offshore Regs now require personal AIS
World Sailing Offshore Special Regulations requiring every crew member to carry a personal AIS As sailors prepare for the 2019 season, awareness is being raised about a rule within the 2018-19 World Sailing Offshore Special Regulations requiring every crew member to carry a personal AIS device when taking part in Category 2 yacht races of extended Posted on 17 Sep
A 95metre mooring extension is now in process
New plans have been unveiled for a 90-metre mooring extension off Auckland's Queens Wharf New plans have been unveiled for a 90-metre mooring extension off Auckland's Queens Wharf to handle cruise ships currently too large for the city. The mooring will have a public gangway for part of its length Posted on 14 Sep
NZ report has common factors with other incidents
Double death investigation exposes common factors with several other deaths and two near-misses Maritime New Zealand's release of its report after an investigation into a double fatality aboard the 20metre yacht Platino, shows several similarities with several other deaths and a couple of near-misses over the past two years in ocean races. Posted on 28 Jul
Report findings on Platino double death
Maritime NZ makes changes following an inquiry into the double death aboard SV Platino Maritime NZ is making changes to safety requirements for recreational vessels leaving New Zealand. The changes come from recommendations in a detailed report into a fatal accident in which two crew members of the yacht Platino died on 13 June 2016. Posted on 26 Jul
Diver unable to work for 12 months after hit
A rookie RIB driver has been ordered to pay $17,500 in reparations for hiting diver - no fine. An Auckland boatie, Carl Allan Whiteman, has been ordered to pay $17,500 in reparation after seriously injuring a diver who he ran over in the water. Mr Whiteman pleaded guilty to one charge under the Maritime Transport Act of causing unnecessary dange Posted on 23 Jul
Report on Kaipara Bar sinking and eight deaths
Boat capsized on second attempt to cross bar - only three of 11 wearing lifejackets The sinking of the Francie, provides a tragic illustration of the importance of lifejackets and the crucial decisions a skipper has to make. Maritime NZ Director, Keith Manch, said seven passengers and the skipper drowned when Francie sank. Posted on 29 Jun
Second skipper fined for not keeping a lookout
In a second, unrelated, case less than a week apart, another skipper has admitted not keeping proper In a second, unrelated, case less than a week apart, another skipper has admitted not keeping proper look-out and has been fined. Posted on 20 May
Fishing boat skipper fined $2000 after loss
Mr Jarman pleaded guilty to the charge under the Maritime Transport Act, and was today fined $2,000 The fishing boat Lady Sarah ran aground on Kaitorete Spit near the entrance to Lake Ellesmere because no one was keeping proper look-out and no one was in the wheelhouse. Posted on 20 May
Fosters - WarehouseSaleNov3-660Sealegs - More Fun 660x82-2North Technology - Southern Spars